Curious Question: How does a Remote Controller Works?

What is inside it? – Basic Version

How it actually works? – Detailed Version

Generally, there are two types of remote controls: infrared (IR), and radio frequency (RF). Infrared remote controls work by sending pulses of infrared light to a device, while RF remote controls use radio waves in much the same way. Pragmatically, the biggest difference between the two is range. IR remote controls require a clear line of sight to the receiving device and their range maxes out at about 30 feet (9.14 meters). RF remote controls can go through walls and around corners, with a range of roughly 100 feet (30.48 meters). 

Do you want to see the Infrared light from your remote.. So simple.. Use the camera in your mobile / a digital camera. Point the remote and press some buttons, you can see the light flashing.

Most home entertainment components such as stereos, televisions and home entertainment centers use IR remote controls. The remote contains an internal circuit board, processor, and one or two Light Emitting Diodes (LEDs). 

When you push a button on a remote control, it transmits a corresponding code to the receiving device by way of LED infrared pulses. The idea is somewhat akin to flashing an SOS signal, but instead of letters, the flashing LED light is transmitting a series of 1s and 0s. The “1” might be represented by a long flash, while “0,” a short flash. A receiver, built into the component, receives the pulses of light and a processor decodes the flashes into the digital bits required to activate the function. 

Along with the desired function, remote controls must also piggyback other data. Firstly, they transmit the code for the device they are controlling. This lets the IR receiver in the component know that the IR signals it is picking up are intended for it. It essentially tells the component to start listening. The function data follows, capped by a stop command to tell the IR device go back into passive mode. 

Some remote controls can be very finicky, requiring the user point the remote directly at the component. This is due to a weak transmitter. Changing the batteries can help, but if the transmitter itself is poor, pulses are transmitted in a narrow beam. More robust IR transmitters, and remote controls with double LEDs, transmit broader beams that allow the user to point the remote in the general direction of the transmitter. 

Sometimes it happens that a recliner or favorite spot on the couch does not have a clear line-of-sight to the entertainment center or television. Often a coffee table or some other object is in the way. When this happens, we find ourselves raising an arm, trying to control the object “around” the device. This can get quite annoying, but there’s an easy alternative. 

Since light bounces off objects it is sometimes more convenient to point remote controls towards a flanking wall or even the ceiling to change a channel or send a function command. The light will bounce off the surface of the wall or ceiling and scatter. If you bounce it at an advantageous angle, the scattering light will reach the component. Often it’s easier, with elbow resting on an armrest, to flip your wrist back and point the remote up on a wall behind you. This can work quite well, even though the remote is pointing in the exact opposite direction of the component. Once you find the easiest sweet spots around the room from which to bounce your signal, you can use these instead of struggling with trying to get around your obstructed line of sight. 

Garage door openers, alarm systems, key fobs and radio-controlled toys use RF remote controls. RF remote controls work essentially the same as IR remote controls, except they use radio waves. As stated, radio waves can also penetrate walls and go around objects and corners, making RF arguably more convenient than IR.

Some high-end entertainment systems come with RF remote controls for an expanded remote range. There are also IR-to-RF remote control converters that allow IR remote controls to extend their range through utilizing a RF translator that basically acts as a middleman. The RF converter relays the IR signal in RF waves to get it further. The converter on the component side reverts the RF signal back to IR so the component can understand it.
 

If you have been overrun by remote controls, you might consider a master universal controller. Low-end universal remotes, available for about 10 US dollars (USD), will allow one to control several devices. However, original remotes might still be required for accessing and controlling an advanced component features. Some high-end universal remote controls feature LCD screens and are more like electronic pads than common remote controls. These universal master controllers will eliminate the need to use original remotes, but may require some ramp-up to learn.

___

Courtesy : Youtube, www.wisegeek.com, Rick OsgoodKarl Wendt

3 thoughts on “Curious Question: How does a Remote Controller Works?

  1. Awesome info Dinesh. Thanks for educating and entertaining as well. Your works all well appreciated.

    Like

We are blogging just for you! Nothing gives fulfillment than your feedback. Love your opinion :)

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s